If the errors continue, replace the drive. Quote Quick Navigation Other Hardware and Devices Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Futuremark Products and Services Futuremark News and Announcements 3DMark - Reinstallation of software which has been affected is your next alternative in case the problem doesn't have to do with viruses. Check cabling and retest. have a peek at this web-site
The Identify Drive Command has not received an acceptable response from the drive. The automatic repair feature can attempt a repair if possible. Re-test Drive 134 Busy Timeout Timeout from checking busy bit. Retest. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711
I am not a techie but I can get into my hard drive area using either ERD Commander or using the Seagate and now the WD Diagnostic Data Lifeguard solutions. Several instances of information on data positioning and location could not be found. It is also possible to see this error on defective Western Digital drives. Re-test Drive 145 FULL STROKE ERROR Error encountered during full stroke seek.
Check cable & retest. This may be due to a defect. Replace the drive if the error repeats. Status Code = 07 (failed Read Test Element), Failure Checkpoint = 97 You may need to rescan to ensure that the repairs were effective.
This error is most likely an internal malfunction of the drive and not related to the condition of the cables etc. 20 Delete Partitions Error Re-test with appropriate diagnostic utility 228 DRIVE IS LOCKED-DST FAIL Security feature of the drive reports locked status. Track 0 also holds information about the drive. http://www.techsupportforum.com/forums/f16/solved-what-is-error-status-code-0132-from-data-lifeguard-diagnostics-537960.html It also may be due to a defective connection.
May need to run DLGUDMA to set the drive to a slower speed or replace the IDE cable. Dlgdiag Code = 07 Failed Read Test Element, Failure 97 Use the appropriate version. This may be due to a media or read/write error. Re-test Drive 139 DRQ NOT EXPECTED The drive did not properly respond to test commands.
Re-test Drive 159 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. http://tomdownload.net/software/western-digital-error-status-code-0132/ Check cabling and retest. Delete Partitions Error Wd However, the computer still won't boot, in Start Windows normally, it goes to black screen with white progress bar and stops, and in Safe Mode, it loads unitl mup.sys then stops Western Digital Error Codes Check cable and retest.
In order for S.M.A.R.T. Check This Out The printer may not be attached or turned on. Windows recovery console doesn't work either *was going to try FIXMBR*. The drive has not responded back in the time allotted. Western Digital Error Code 0007
Check your floppy and retest. Re-Test Drive 104 Drive Not Ready The drive did not properly respond to test commands. The drive may not have been accessed properly possibly due to a bad connection. Source Re-test Drive 162 READY EXPECTED Timeout from checking busy bit.
Several instances of information on data positioning and location could not be found. Wd Bad Sector Repair Tool Replace the drive if the error repeats. This may be due to a media error.
An onboard defect counter has determined the drive has too many errors and should be replaced. If the automatic repair feature is unable to repair these errors, replace the drive. This may be due to a media or read/write error. Wd My Passport Smart Status Failed This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection.
This error may have internal and external reasons. There are too many errors detected on this drive to be repaired. This may be an anomaly or a defect with the drive. http://softwarenegozi.net/western-digital/western-digital-diagnostics-error-code-0132.html Re-test Drive 137 Relocated Sector Sector Relocated.
So, I downloaded the WD Data Lifeguard Diagnostic software, had to use the one with the ISO Another anyway, can someone please assist me in figuring out what might be happening, No Errors 0001-0015 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. Please ensure that you are using the version of diagnostic utility corresponding to either newer or older Western Digital drives. This may be an anomaly or a defect with the drive.
Retest after checking the connections. Version 4.12 for older drives and version 5.00 for current drives. Replace Drive 161 RESET SIGNATURE The drive did not properly respond to test commands. Recheck your connections and replace the cable.
Retest. Replace Drive 213 2-9 DAM Errors Data Address Mark (DAM) 2-9. When I did a c:\dir it listed the contents of what was my F drive (secondary HDD). Re-Test Drive 111 DIAG COMMAND ERROR The drive did not properly respond to test commands.
Re-test Drive 201 Non-WD Drive The drive does not have a WD serial number. This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested. Check cabling & retest. Please contact the system vendor for the above-mentioned information.
For some individuals, dealing with the error is a waste of time thats why they plan to install a brand new operating system. Replace Drive 219 Drive Cable Error Failure during cable test. Re-Test Drive with latest diagnostic utility 117 Uncorrectable ECC Error Uncorrectable Error Correction Code (ECC) Error. Re-test Drive 220 Drive is Locked Security feature of the drive reports locked status.
© Copyright 2017 softwarenegozi.net. All rights reserved.